{"product_id":"ak-interactive-streaking-effects-35ml","title":"AK Interactive Streaking Effects 35ml Enamel – Weathering Grime for Models","description":"\u003cdiv class=\"product-description\"\u003e\n\n\u003ch2\u003eEnamel Streaking Grime and Rust for AFV, Ship and Sci-Fi Modeling\u003c\/h2\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePre-Mixed Enamel Streaks\u003c\/strong\u003e – Ready-to-use pigment density in a 35ml jar. No oil paint mixing, no test panels, no thinner ratios to dial in before starting the build.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTwo-Brush Workflow\u003c\/strong\u003e – Draw vertical lines with a fine brush, wait ten minutes, soften with a damp flat brush. The drag-down step turns drawn lines into convincing weathering.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDoubles as Pin Wash\u003c\/strong\u003e – Diluted with white spirit, capillary flow pulls the enamel into panel lines and around rivets for clean panel-line work alongside the streaking pass.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eReactivates with White Spirit\u003c\/strong\u003e – Enamel chemistry stays workable for hours. Soften, blend, or remove streaks with a clean brush and thinner until the effect reads right.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003e📝 About the Streaking Effects Range\u003c\/h2\u003e\n\n\u003cp\u003eAK Interactive built this enamel line because mixing oil paint streaks the old way was inconsistent — too thick one session, too thin the next. Each 35ml jar is pre-mixed at the correct pigment density for vertical-line application, so the bottle you opened a year ago and the one you open today lay down the same streak. That batch consistency is why competition modelers and YouTube tutorial channels stayed with this line through three Spanish manufacturing eras.\u003c\/p\u003e\n\n\u003cp\u003eApplication chemistry is enamel — solvent-based — which sits stable on top of fully cured acrylic or lacquer paint without lifting the underlying color. Build your base coat in any acrylic system (Vallejo, AK 3GEN, Tamiya) or lacquer (Mr. Color, Tamiya lacquer), seal with gloss clear, and apply this enamel streak on top without chemistry conflict. Cleanup uses White Spirit or odorless mineral spirits — never water, never lacquer thinner.\u003c\/p\u003e\n\n\u003ch2\u003e🎯 Color Selection Guide\u003c\/h2\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-012 Streaking Grime\u003c\/strong\u003e – Brown-tan dirt for Dark Yellow \/ RAL 7028 Dunkelgelb late-war German armor (Panther, Tiger I, StuG III), also reads correctly on US Olive Drab and British Caunter scheme\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-013 Rust Streaks\u003c\/strong\u003e – Universal rust for any rivet, exhaust, fuel cap, or metal-on-metal wear point. Works on AFV, naval, aircraft, and industrial subjects\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-014 Winter Streaking Grime\u003c\/strong\u003e – Light grey-tan for whitewashed Eastern Front armor, modern Arctic vehicles, and snow-camo aircraft\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-024 Dark Streaking Grime\u003c\/strong\u003e – Darkest in the range, for Olive Drab Sherman \/ M4, Soviet 4BO green, and modern jungle camouflage\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-067 Streaking Grime for DAK Vehicles\u003c\/strong\u003e – Afrika Korps Panzer III and Panzer IV in RAL 8000 Gelbbraun, also reads correctly on Italian M13\/40 and Carro Armato sand-yellow\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-069 Streaking Grime for Panzer Grey\u003c\/strong\u003e – Cool-toned grime for early-war German armor in RAL 7021 Panzergrau (Panzer III Ausf E\/F, early Tiger I, StuG III Ausf B–E)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-074 Rain Marks for NATO Tanks\u003c\/strong\u003e – Light water-trail effect for tri-color Bronzegrün\/Lederbraun\/Teerschwarz camo on Leopard 2, US M1 Abrams, British Challenger 2\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-094 Streaking Grime for Interiors\u003c\/strong\u003e – Light tones for tank crew compartments, aircraft cockpits, vehicle cabs, and APC interiors where exterior grime reads too dark\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-123 OIF and OEF US Vehicles Streaking\u003c\/strong\u003e – Iraq\/Afghanistan-era modern desert dirt over FS 33446 sand camo (M1A2, Stryker, MRAP, M-ATV)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-304 Brown Streaking Grime for Red Hulls\u003c\/strong\u003e – Rust-streaked weathering for red oxide anti-fouling primer below the waterline on naval models\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-305 Streaking Grime for Light Grey Ships\u003c\/strong\u003e – US Navy haze grey, Royal Navy 507A\/507B, and Imperial Japanese Navy Kure grey upper hull and superstructure\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-306 Salt Streaks for Ships\u003c\/strong\u003e – White salt crusting at and just above the waterline, also for harbor scenes and coastal equipment dioramas\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAK-637 Starship Streaking Grime\u003c\/strong\u003e – Sci-fi mecha, Gundam (HG\/MG\/PG), Bandai Star Wars kits, Warhammer 40K vehicles, and futuristic spacecraft fuselages\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eFor German WWII armor:\u003c\/strong\u003e AK-012 over Dark Yellow late-war, AK-069 over Panzer Grey early-war, AK-067 over DAK desert sand, AK-024 for any dark green or dark brown surface needing streak depth.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eFor Allied and modern AFVs:\u003c\/strong\u003e AK-024 as the all-purpose green\/brown choice, AK-074 for NATO tri-color camo, AK-123 for OIF\/OEF deployment-specific desert dirt.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eFor ship hulls:\u003c\/strong\u003e AK-304 below the waterline on red anti-fouling primer, AK-305 upper hull and superstructure, AK-306 waterline salt crusting. The combination covers a complete naval weathering pass.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eFor sci-fi, Gundam, and Bandai mecha:\u003c\/strong\u003e AK-637 for fuselage panels where military-vehicle dirt reads too organic. Works on Gunpla, Warhammer 40K, and futuristic spacecraft.\u003c\/p\u003e\n\n\u003ch2\u003e💡 How to Use\u003c\/h2\u003e\n\n\u003cp\u003e\u003cstrong\u003eStep 1 — Surface prep:\u003c\/strong\u003e Apply over fully cured paint (24+ hours after the last paint coat). For acrylic base coats, seal with gloss clear (AK Gauzy Shine, Tamiya X-22, or Mr. Color C46) before streaking — the gloss layer protects underlying paint from solvent re-wetting and gives the enamel a smooth surface to grip. Dead-flat finishes absorb the streak and lock it in place permanently.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eStep 2 — Apply vertical lines:\u003c\/strong\u003e Shake for 30+ seconds. Load a fine pointed brush (size 0 or 00 synthetic) and paint irregular vertical streaks running down from upper panels, hatches, hinges, exhausts, and fuel caps. Vary streak length and spacing — uniform streaks read as fake.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eStep 3 — Wait 10 minutes.\u003c\/strong\u003e The enamel needs to set partially before blending. Too soon and it smears entirely; too late and it locks in place. Ten minutes is the sweet spot for 35ml-bottle viscosity at room temperature.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eStep 4 — Feather with White Spirit:\u003c\/strong\u003e Dampen a clean flat brush (size 4–8 synthetic) in AK-011 White Spirit or AK-047 Odorless Turpentine — flick excess so the brush is moist, not wet. Drag vertically downward through the streak with light pressure, breaking the hard line into a soft graduated dirt run. Wipe between strokes.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eDecal timing:\u003c\/strong\u003e Apply streaks \u003cem\u003eafter\u003c\/em\u003e decals are placed and sealed. Decals go down on a gloss surface, get sealed with another gloss layer, then receive the streaking pass. Streaking before decals causes silvering when the decal solvent reactivates the enamel underneath.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eCleanup \u0026amp; cure:\u003c\/strong\u003e Clean brushes immediately with White Spirit while the enamel is still active. Once cured (24 hours), the streak is ready for varnish overcoat or further weathering layers (pigments, oil dot work, chipping). Sealing with a satin or matte clear coat between weathering passes prevents earlier layers from reactivating when fresh enamel is applied on top.\u003c\/p\u003e\n\n\u003ch2\u003e⚓ Ship Hull Workflow Note\u003c\/h2\u003e\n\n\u003cp\u003eNaval modelers using the three ship-specific colors (AK-304, AK-305, AK-306) typically apply in this order: complete the hull paint and gloss-seal it, then apply \u003cstrong\u003eAK-304\u003c\/strong\u003e below the waterline on the red oxide primer first. Let it cure for 24 hours and seal with a thin satin clear before moving above the waterline. Apply \u003cstrong\u003eAK-305\u003c\/strong\u003e on the upper hull and superstructure, blending with white spirit. Last, apply \u003cstrong\u003eAK-306 Salt Streaks\u003c\/strong\u003e at and just above the waterline boundary — this is the layer most exposed to handling damage during display, so it goes last and gets a final matte clear seal for protection.\u003c\/p\u003e\n\n\u003ch2\u003e❓ Frequently Asked Questions\u003c\/h2\u003e\n\n\u003cp\u003e\u003cstrong\u003eMy streaking came out too dark or too heavy — how do I fix it?\u003c\/strong\u003e\u003cbr\u003e\nReactivate with White Spirit. Dampen a clean flat brush in AK-011 or AK-047, drag downward through the over-applied area with light pressure, and wipe the brush frequently to remove the excess pigment you're pulling off. This works as long as the streak hasn't fully cured (within 24 hours of application). After full cure, removal requires more aggressive solvent and risks lifting underlying paint — so always check the streak intensity before walking away from the bench.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhich White Spirit should I buy — AK-011 or AK-047?\u003c\/strong\u003e\u003cbr\u003e\nAK-011 is the standard White Spirit, slightly faster-evaporating and what AK references in their tutorials. AK-047 is an odorless turpentine alternative for shared workspaces or smell sensitivity — slightly slower evaporation, otherwise functionally identical. Either works for thinning and feathering.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eCan I apply this directly over Vallejo or Tamiya acrylic without a clear coat?\u003c\/strong\u003e\u003cbr\u003e\nPossible but risky. The enamel solvent can re-wet the underlying acrylic if it isn't fully cured (48+ hours minimum). The safest workflow is: acrylic base coat → 24+ hour cure → gloss clear coat → enamel streaking → feather with White Spirit. Skipping the gloss seal works on small areas but increases the risk of lifting paint when you feather.\u003c\/p\u003e\n\n\u003ch2\u003e📐 Specifications\u003c\/h2\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e AK Interactive\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct Line:\u003c\/strong\u003e Streaking Effects (Enamel)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVolume:\u003c\/strong\u003e 35ml glass jar with shaker bead\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFormula:\u003c\/strong\u003e Solvent-based enamel, white-spirit-soluble\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Brush only (not airbrush-compatible)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCompatible Solvents:\u003c\/strong\u003e AK-011 White Spirit, AK-047 Odorless Turpentine, generic odorless mineral spirits\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCompatible Base Coats:\u003c\/strong\u003e Cured acrylic, lacquer, and enamel paint surfaces\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNOT Compatible With:\u003c\/strong\u003e Wet or partially-cured base paint (will reactivate underlying layer)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDrying Time:\u003c\/strong\u003e 10 minutes touch-set for blending; 24 hours full cure\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAvailable Variants:\u003c\/strong\u003e 13 colors (see variant selector above)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCountry of Origin:\u003c\/strong\u003e Spain\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHazard Classification:\u003c\/strong\u003e Solvent-based — work in a ventilated area. Keep away from heat and open flame.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBest For:\u003c\/strong\u003e AFV weathering, naval ship hulls, aircraft panels, Gunpla and Bandai kits, Warhammer 40K vehicles, diorama scenery\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003c\/div\u003e","brand":"AK Interactive","offers":[{"title":"Streaking Grime – AK012","offer_id":47779546628322,"sku":"AK-012","price":4.48,"currency_code":"USD","in_stock":true},{"title":"Rust Streaks – AK013","offer_id":47779546661090,"sku":"AK-013","price":4.48,"currency_code":"USD","in_stock":true},{"title":"Winter Streaking Grime – AK014","offer_id":47779546693858,"sku":"AK-014","price":4.48,"currency_code":"USD","in_stock":true},{"title":"Dark Streaking Grime – AK024","offer_id":47779596861666,"sku":"AK-024","price":4.48,"currency_code":"USD","in_stock":true},{"title":"Streaking Grime for DAK Vehicles – AK067","offer_id":47779546726626,"sku":"AK-067","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Streaking Grime for Panzer Grey – AK069","offer_id":47779546759394,"sku":"AK-069","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Rain Marks for NATO Tanks – AK074","offer_id":47779546792162,"sku":"AK-074","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Streaking Grime for Interiors – AK094","offer_id":47779546824930,"sku":"AK-094","price":4.48,"currency_code":"USD","in_stock":false},{"title":"OIF \u0026 OEF US Vehicles Streaking – AK123","offer_id":47779546857698,"sku":"AK-123","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Brown Streaking Grime for Red Hulls – AK304","offer_id":47779596894434,"sku":"AK-304","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Streaking Grime for Light Grey Ships – AK305","offer_id":47779596927202,"sku":"AK-305","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Salt Streaks for Ships – AK306","offer_id":47779596959970,"sku":"AK-306","price":4.48,"currency_code":"USD","in_stock":false},{"title":"Starship Streaking Grime – AK637","offer_id":47779596992738,"sku":"AK-637","price":4.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0622\/2014\/0770\/files\/AK-Interactive-Streaking-Effects-Enamel.jpg?v=1778125883","url":"https:\/\/happibee.com\/products\/ak-interactive-streaking-effects-35ml","provider":"Happibee","version":"1.0","type":"link"}